Machines in stock

MINIMUM CONTACT GRAVITY CONVEYOR

min contact gravity conveyor

MODEL # – Minimum Contact Gravity Conveyor

SERIAL # – 986419137

CONDITION – DEMO

CATEGORIES – Material Handling

Designed to handle panels or other materials at the entrance and exit of in-line applicator equipment during the manufacturing process. Minimum contact discs ensure the weight of the panels or materials is not supported on the glue rollers allowing for an undisturbed and perfectly sealed finished product.

Disks mounted on 12″ centers, disks mounted on 3/4″ diameter stainless steel axles on 12″ centers, axles mounted in double sealed 3/4″ heavy duty bearings, heavy duty frame 30″ x 75″ with adjustable food pads (approx. work area 42″ x 120″), complete with optional removable stainless steel wash pan with easy to remove cleaning drain and swivel block.

min contact gravity conveyor

VACUUM THERMOFORMER MODEL TF3-4-8

MODEL # – ThermoFormer Model TF3-4-8

SERIAL # – 369630

CONDITION – DEMO

CATEGORIES – 3D Machines and Accessories

3D ThermoFormer Model TF3-4-8 BLACK BROS. 3D ThermoFormer Model TF3-4-8

Designed for 57” wide 3DL (1400 & 1450 mm)
220 – 230 Volt, 3 Phase, 60 Hertz, 24VDC Control Circuits

Complete With:
(2) Single Loading Trays with Frame Clamps. Useable area is approx. 48” x 96” (1220 mm x 2440 mm). Clamp frame opens by air cylinder.
Minimizer with Rubber Gasket to seal unused area of the tray
On-board Allen Bradley PLC controller with Panel View C-600 Touch Screen
Capable of 9 programs or “recipes,” controller mounted on the press.
3 HP Vacuum Pump
Infra-red bulb heaters 375-Watt
Simple 2-roll 3DL (3-dimensional laminate) rack (no casters)
(600) Magnetic Starter Pins (per tray)
Standard Paint BBCO White for press enclosure.  Everything outside press enclosure to be BBCO Blue

Press Specification:
• Press system: Vacuum/heat chamber
• Press body: Welded tubular steel with sheet metal
• Tray dimension, outer edge: 58.5 ” x 106.5” (1490 x 2705 mm)
• Tray dimension, inner edge: 52.5” x 100.5” (1335 x 2550 mm)
• Practical usable area: 48” x 96” (1220 x 2440 mm)
• Height of tray: 2.0” (50.1 mm)
• Overall height of press chamber: 5.0” (125 mm)
• Heating oven design: Reflective shielding with IR bulbs
• Maximum temperature: 350°F (175°C)
• Working table height approx.: 36” (915 mm)
• Vacuum pump: 3 HP
• Maximum chamber pressure: 14.5 psi. (1 kg/cm2) Vacuum
• Dimensions (W x L x H): 71” x 226” x 62” (1803 x 5740 x 1575 mm)
• Approximate Weight: 2,950 pounds (1340 kg)

Electrical Specification:
• Operating power supply: 230 volt / 60 hertz / 3 phase

Press Time
• Pressing time depends on the type and thickness of the laminate, the press temperature, the adhesive formula and other factors. Due to the number of variants, it is impossible to accurately predict the press time.
• A pressing cycle of 150 seconds can be achieved with most standard 3DL’s.

Pressing Programs
(Single-sided lamination of a contoured substrate surface)
• Using the machine to press standard 3DL’s to the substrate
• Using the machine with a membrane to press veneer to the substrate
• Pressing 3DL without the membrane

 Pressing Area
(Net pressure chamber height = lower tray cavity + upper tray frame cavity)
• Maximum chamber height with a 2” deep tray is 5”, however, the ability to utilize that dimension will vary based on the geometry of the parts, and the thickness of the 3DL.
• Maximum usable area is 48” x 96”.
• Maximum part height = work piece height + pedestal/template height (recommended not to exceed 2.75”).

Pressing Materials
• Substrates: the machined profile of the substrate should be matched to the laminate, and the working parameters of the machine.
– MDF (double refined yields best definition)
– Particle board and other acceptable substrates.
• Laminating overlay material
– 3DL (3-dimensional laminate) like PVC, ABS, PO, PET, PETG, APET which are suitable for the pressing procedure
– Heat Transfer Foils
• Laminating Adhesives
– One-part and Two-part water based polyurethane dispersion

3D Thermoformer Model TF3-4-8 3D Thermoformer Model TF3-4-8

775 SINGLE TOP HOT MELT ADHESIVE SPREADER

775 Hot Melt Adhesive Spreader

MODEL # – 775 Single Top Hot Melt Glue Spreader

SERIAL # – 383923

POWER SUPPLY – 460 Volt, 3 Phase, 60 Hertz

CONDITION – DEMO

CATEGORIES – Adhesive Spreaders & Roll Coaters

 
 

Application: To apply Reactive Hot Melt Adhesive or PUR to the top surface of Substrate at temperatures up to 350 Degrees F.

Nominal Length: 68″. Standard Pass Line Height: 30″ Upper Elevator: 0 to 4-1/2″ opening. Top Exhaust 8″ Outlet. Operating Controls and Hand-wheels: left end

Motorized Auto-Elevator with Encoder: Operator interface terminal in control panel w/ speed and roll opening display.

Doctor Roll and Coating Roll heated by rotary joint: with counter-flow on one end

Single Hand-wheel Doctor Roll Adjustment – Hand-wheel perpendicular to direction of flow includes mechanical digital read-out in .001″ increments

Independent Drive on Doctor Roll A.C. Inverter 2-20FPM

Variable Speed Drive: A.C Inverter Type, 30-90 FPM with 3″ Reverse Lock-out

Centralized Lubrication Manifolds: elevating gear boxes and bearings.

NEMA 12 Enclosure with main power disconnect switch and over-current protection: 460 Volt, 3 Phase, 60 Hertz, 24 VDC Control Circuits

Premium Teflon® Coating: guards, tables, end seal backing plates. Solid High Temp End Seals: with auxiliary end seal insert

Electric Oil Heat Transfer System: With Centrifugal Pump Mounted on Common Base: with separate controls for oil heater on right end. Filled and factory tested with heat transfer oil

775 SINGLE TOP HOT MELT GLUE SPREADER

775 SINGLE TOP HOT MELT GLUE SPREADER

WEB REWIND STAND

Rewind

MODEL # – REWIND STAND

SERIAL # – 377457

POWER SUPPLY  – 460 Volt, 3 Phase, 60 Hertz

CONDITION – DEMO

CATEGORIES – Material Handling

 

Web Rewind Stand: linear actuator for rewind stand edge controls. Web tension control using dancer arm; w/ Automatic web guidance system. Will handle roll stock from 6″ to 61″ wide, 700 lbs. and 20″ in diameter w/aluminum Air shafts, 3″ & 6″ cores. With safety chucks.

Nominal Length: 68″

NEMA 12 Enclosure with main power disconnect switch and over-current protection: 460 Volt, 3 Phase, 60 Hertz, 24 VDC Control Circuits

Speed: 30 FPM

Controls on Left

Rewind

DIFFERENTIAL DIRECT/REVERSE ROLL COATER (DDRC)

DDRC

MODEL # – Differential Direct/Reverse Roll Coater

SERIAL # – 377672

POWER SUPPLY – 460 Volt, 3 Phase, 60 Hertz

CONDITION – DEMO

CATEGORIES – Adhesive Spreaders & Roll Coaters

 

This Differential Direct/Reverse Roll Coater has a nominal length of 56″ and a standard pass line height of 30″.

For more information, please contact us via your sales associate, our contact form, our toll-free number 800-252-2568, or email us at info@blackbros.com.

DDRC

In stock to Purchase Today

RL 750 — ROTARY LAMINATOR

MODEL # – RL-750

SERIAL # – 390546

POWER SUPPLY – 460 Volt/3 Phase/60 Hertz

CONDITION – DEMO

CATEGORIES – Rotary Press

 

This RL-750 Rotary Laminator has a nominal length of 68″ and a riser base for a pass line height of 36″. It includes single speed drive, infeed and outfeed barrier guards and feed tables, and standard NEMA 12 Electrical Enclosure.

For more information, please contact us via your sales associate, or email info@blackbros.com.

775 SINGLE TOP HOT MELT ADHESVIE SPREADER

MODEL # – 775 Single Top Hot Melt Glue Spreader

SERIAL # – 387762

POWER SUPPLY – 460 Volt/3 Phase/60 Hertz

CONDITION – DEMO

CATEGORIES – Adhesive Spreaders and Roll Coaters

 

Application: To apply Reactive Hot Melt Adhesive or PUR to the top surface of Substrate at temperatures up to 350 Degrees F.

Nominal Length: 26″. Standard Pass Line Height: 30″ Upper Elevator: 0 to 4-1/2″ opening. Top Exhaust 8″ Outlet. Operating Controls and Hand-wheels: left end.

Motorized Auto-Elevator with Encoder: Operator interface terminal in control panel w/ speed and roll opening display.

Doctor Roll and Coating Roll heated by rotary joint: with counter-flow on one end.

Single Hand-wheel Doctor Roll Adjustment – Hand-wheel perpendicular to direction of flow includes mechanical digital read-out in .001″ increments.

Independent Drive on Doctor Roll A.C. Inverter 2-20FPM.

Variable Speed Drive: A.C Inverter Type, 30-90 FPM with 3″ Reverse Lock-out.

Centralized Lubrication Manifolds: elevating gear boxes and bearings.

NEMA 12 Enclosure with main power disconnect switch and over-current protection: 460 Volt, 3 Phase, 60 Hertz, 24 VDC Control Circuits.

Premium Teflon® Coating: guards, tables, end seal backing plates. Solid High Temp End Seals: with auxiliary end seal insert.

Electric Oil Heat Transfer System: With Centrifugal Pump Mounted on Common Base: with separate controls for oil heater on right end. Filled and factory tested with heat transfer oil.

RPP-C-1575 — ROATARY PNEUMATIC PRESS

MODEL # – 1575 CRPP

SERIAL # – 389285

POWER SUPPLY – 460 Volt/3 Phase/60 Hertz

CONDITION – DEMO

CATEGORIES – Rotary Press

 

The Black Bros. C1575 Rotary Pneumatic Press is designed especially for laminating heat-sensitive adhesive films or thermally softened substrates in roll-to-roll applications. Its large diameter rolls and reinforced, durable construction yield outstanding heat transfer performance on a wide range of materials up to 200 fpm.

775 TOP AND BOTTOM ADHESIVE SPREADER

MODEL # – 775 Adhesive Spreader

SERIAL # – 390547

POWER SUPPLY – 460 Volt/3 Phase/60 Hertz

CONDITION – DEMO

CATEGORIES – Adhesive Spreaders and Roll Coaters

 

This Black Bros. 775 Adhesive Spreader is a basic model built for durability and excellence. It provides a compact, reliable and economical approach to adhesive spreading for standard size materials. The efficient design with fewer components than other models makes ease of use and a long life.

contact us button

What is Lorem Ipsum?

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry’s standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.